Domain Tools

Vehicle misfires, does not acellerate well, seem to be underpowered, loss of power, low power.

Duration : 0:2:15

Read the rest of this entry »

2003 Dodge Ram 1500 4×4 5.9L

Customer Complaint = Check engine light On, Vehicle does not shift properly, code P1762 stored in memory

Procedure:

1. Check the voltage of the governor pressure sensor with the Key On Engine Off (KOEO). It should be about 0.5 volts.

2. If higher than 0.8 volts, check the transmission temperature sensor reading.

3. If it is not accurate, check the sensor ground to the governor pressure/transmission temperature sensor.

4. If the transmission temperature sensor is reading correctly, replace the governor pressure sensor.

Potential Causes:

Evaporative Line
Gas Cap
Purge Solenoid
Vent Control Solenoid

Confirmed Fix:

1 – Governor Pressure Sensor
1 – Transmission
1 – Transmission Fluid

Duration : 0:2:6

Read the rest of this entry »

2003 Honda Accord DX 2.4L

Customer Complaint = ABS light is on after repairing wheel bearings

Procedure:

1. Check the wheel bearing, it has a Brown dust shield behind the dust shield is the encoder, and the Brown dust shield should go to the inside of the knuckle.

2. If installed backwards, it will set this code.

Potential Causes:

Improperly Installed Bearing

Confirmed Fix:

Improperly Installed Wheel Bearing

Duration : 0:1:42

Read the rest of this entry »

The new video based inspection scope is a great specialty tool for automotive and home inspections used by auto technicians, mechanics, plumbers, electricians, professional home inspectors etc. more information available at DenLorsTools.com.
http://www.denlorstools.com/home/dt1/page_13223_507/visual_optics_vs36_10ww_vo_scope_inspection_stik_f.html

Duration : 0:1:9

Read the rest of this entry »

http://www.denlorstools.com/autoblog/ Bench bleeding the brake master cylinder before installing it on the car is necessary to help remove the air so normal pedal firmness and height can be obtained. For the entire auto tech article and access to great deals on automotive tools visit http://www.denlorstools.com/home/dt1/page_7445/automotive_brake_bleeding_exclusive_tech_article.html Also see our Auto Repair Industry Blog at http://www.denlorstools.com/autoblog/

Duration : 0:1:5

Read the rest of this entry »

2000 BMW 528 IT 2.8L M52TU

Customer Complaint = Vehicle does not accelerate well, seems to be underpowered. Check engine light illuminated and a code P0340 (BMW 65) set

Procedure:

1. Test wiring at the sensor connector:

A. Pin 1 (Red/White wire) should have battery voltage with ignition on.

B. Pin 2 (Yellow) should have 5V from engine control module.

C. Pin 3 (Brown) is a ground.

2. As the cam turns, the 5V reference on pin 2 should switch on and off (5V square-wave digital signal).

Potential Causes:

Defective Camshaft Position Sensor (CMP)
Wiring

Confirmed Fix:

3 – Camshaft Position Sensor (CMP)
2 – Intake Camshaft Position (CMP) Sensor
1 – Crankshaft Position (CKP) Sensor

Duration : 0:2:20

Read the rest of this entry »

2002 Toyota Tacoma 3.4 Ltr. Engine,

The Check Engine Light (CEL) is on with a trouble code P1135. The code indicates that there is a problem with the ban 1 sensor 1 Air/Fuel (A/F) ratio sensor.

Test/ Procedures:
1. First Verify that the resistance specification for the heater circuit are 0.8 to 1.4 ohms at 68 degrees and 1.8 to 3.2 ohms at 1400 degrees.

2. If the resistance at the heater circuit is OK, verify that there is a good battery voltage to the sensor and the resistance is correct.

3. Next, check for the correct current flow on the circuit. It needs to draw more than 0.25 amps and less than 8 amps when the Oxygen sensor heater is grounded.

Pttential Causes:

Air Fuel Ratio Sensor
Connection
Fuse

Duration : 0:3:12

Read the rest of this entry »

QUALITY PROFESSIONAL DR BRAND AIR TOOLS MADE BY GREEN KENT INC.

VISIT WWW.DRAIRTOOLS.COM FOR MORE INFORMATION!

Duration : 0:3:39

Read the rest of this entry »

2000 Volvo S40 1.9L

Customer Complaint = Check Engine Light On, code P0128 set in memory

Procedure:

1. Test actual ECT and compare to indicated temperature on scan tool.

2. If they agree, the engine is probably warming up too slowly because of a leaking thermostat.
3. Replace the thermostat, clear the code and test-drive.

Potential Causes:

Engine Coolant Temperature (ECT) Sensor
Thermostat

Confirmed Fix:

3 – Engine Coolant Temperature (ECT) Sensor, Thermostat
1 – Coolant Temp Sender, Thermostat
1 – Cylinder Head Gasket

Duration : 0:2:44

Read the rest of this entry »

What tools are needed to recharge or retrofit an auto A/C system? Learn about recharging a car’s air conditioner with refrigerant in this free car maintenance video.

Expert: Nathan McCullough
Bio: Nathan McCullough graduated from Nashville Auto-Diesel College with a GPA of 3.5. He has managed several automotive facilities over the last eight years.
Filmmaker: Robert Rogers

Duration : 0:1:25

Read the rest of this entry »